Auto Detailing Wet Dry Central Vacuum

Add to Cart
Free Shipping from contractors Store. Craig 239-357-1853.




We can figure out everything you will need for your job if you give us your specs.









Ideal for commercial buildings, large boarding kennels and detail shops etc.









AQUA-AIR Wet/Dry Central Vacuum Power Units.









Wall mounted central vacuum power units provide high volume dry vacuuming and quick drying wet extraction. Water rinse and cyclonic action separates the water, dirt, and debris without the restriction of filters. Waste tank automatically rinses and flushes all water and dirt down the drain. Central vacuum power units connect to multiple vacuum inlet/water outlet stations via water lines and vacuum tubing.









Aqua Air AA004 W/8.4 - Model 258 Heavy Duty Central Vacuum Unit & Wet Extractor with 2 Motors.














•Dual Canister System: Power unit is attached to Debris Separation Tank




•Dual Canister Units provide easy cleaning in high volume dirt and debris situations




•Two 8.4" Extractor Motors, 2 stage, High Efficiency, epoxy coated sealed bearings




•Each motor rated at 146" Water Lift




•283 CFM




•14 amp, each motor




•120 volts




•Suitable for up to 10,000 square feet




•Seperation Tank and Power Unit can be mounted separately from each other




•Power Unit (motor canister) 14" x 33"




•Debris Separation chamber 14" x 47"




•Two operators at the same time




•Ideal for commercial buildings, large boarding kennels and detail shops etc.





























RECOVERY TANK: The cyclonic separator and cold water spray separate the water, foam and debris from the air flow without restrictive filters or mechanical floats. Large debris is contained in a mesh screen while the liquids automatically dump down the drain.









UTILITY REQUIREMENTS:




ELECTRICAL: 120 volt, 60 hertz, 15 amp standard plug









WATER: Cold water with shut-off. Hot water (up to 170°F [77°C]) with shut-off. Connect directly to water outlets or to optional cleaning solution injector (AA031 or AA033).









DRAIN: 2" DWV drain to sewer. A p-trap will be required and vent to meet plumbing codes.









EXHAUST: If power unit is located in a small room, exhaust air from the vacuum motor must be exhausted to the outside of the building using the most direct route possible.









INSTALLATION:




POWER UNIT: Locate in an area where it will be protected from freezing. The mounting bracket should be firmly attached to a wall stud or masonry wall. A minimum space of 12" is required from the ceiling and on each side of the unit. The unit must be mounted high enough above the floor as to allow for drain connection and easy access to service the debris screen.









Vacuum inlets are conveniently located near doorways, in hallways or other centrally located areas. The vacuum lines are regular 2" PVC vacuum tubing and fittings.









WATER OUTLETS: Water Outlets are located next to the vacuum inlets. (In existing structures where access is limited the outlets may be located under sinks or on other wall where access is possible. The water lines may be either 3/8" or 1/2" PEX, 3/8" copper or other equivalent tubing appropriate for the building with connections made in accessible areas.









COMMERCIAL LIMITED WARRANTY: The manufacturer warrants to the initial purchaser that the AQUA-AIR Wet/Dry° power unit and cleaning solution injector will be free from defects in material and workmanship for one (1) year from the date of the first consumer purchase or one thousand (1000) hours whichever occur first, and that hoses, tools and other attachments will be free from defects in material and workmanship for ninety (90) days from the date of the first purchase.









Aqua Air YouTube Videos.









http://youtu.be/FdTpZOPQ6rE









http://youtu.be/6bkBib3dQMQ









http://youtu.be/inU6JAhakBM









http://youtu.be/z7-ze8rcfo0



















Free Shipping from Contractors Store. 239-357-1853 Craig














assembled in the usa Designed & Assembled in the USA.









For shipping to Alaska, Hawaii and Canada call for pricing.
    • Brand Aqua Air
    • Mfg Part # AA004 W/8.4
Payment Methods
Shipping FREE Shipping
Return/Exchange Policy

Return Policy.

A Return Goods Authorization (RGA) number must be obtained from customer service (1-239-357-1853). Products must be unused and in their original cartons. No discontinued or obsolete items will be accepted. For safety reasons, no returns can be accepted on HEPA items. Customer pays return freight charges and 20% restocking fee, We reserves the right to refuse any return not in compliance with the above.

Please Login or Register first before asking a question.
More from ContractorsStore's Store